Small-Hole Boring Bar Selection Guide: Bore, Nose Radius and Reach
Share
Most boring bars don't fail because the carbide is poor. They fail because the bar is asked to reach further than its diameter can support, or because a nose radius was chosen for finish on a job that needed edge strength. Both mistakes look the same at the machine: chatter, a chipped tip, a scrapped bore.
This guide covers the four numbers that decide whether a bar will survive the bore, how to read a BB Tool variant code, and which series fits each internal operation.
Start with four numbers, not with a series
Before opening a catalogue, write these down:
- Minimum bore diameter — the smallest hole the cutting head must enter, not the nominal bore on the drawing.
- Bore depth — how far the cutting edge has to reach from the holder face.
- Feature type — straight bore, internal groove, thread, profile or face groove. Each needs different clearance behind the edge.
- Machine interface — collet, boring head or clamp holder, and the shank diameter it accepts.
Minimum bore is the hard constraint, and it is set by geometry rather than by cutter diameter alone. The cutting head, its relief and its chip clearance all have to fit inside the hole while the shank stays outside it. That is why a bar with a 3 mm shank can still enter a bore well under 3 mm — the shank is not the part that goes in.
On the MGR and MNR grooving series, the smallest listed sizes reach approximately 2.1 mm bore diameter. Below that, the limit stops being the tool and becomes the rigidity of the machine and setup.
Depth is the second constraint, and the one people underestimate. A bar that reaches 15 mm at D4 is a different tool from one that reaches 22 mm at D4, even when both sit under the same series name.
How to read a variant code
The codes follow a consistent order: series, size, then the dimension that defines the cut — nose radius (R) on boring and profiling bars, groove width (B) on grooving bars — then cutting length, and shank diameter only where it changes within a series.
Take MTR1 R0.05 L4-D3. MTR is the series, 1 is the size step, R0.05 is the nose radius, L4 is the cutting length, and D3 is the 3 mm shank. When the shank is constant across a series, the D suffix is left off — MQR4 R0.1 L15 has no suffix because every MQR4 in that group uses the same shank.
Read the size number as the series' own sizing step, not as a bore diameter and not as a shank. It moves in the same direction as both — larger number, larger bore and larger shank — but confirm the exact figure on the product page before ordering.
Which series for which internal operation
The series letters describe geometry, not quality tiers. A higher number is not a better bar; it is a bar built for a different cut.
| Operation | Series | What it is for |
|---|---|---|
| Boring and internal turning | MQR, MUR, MTR, MNR | Straight bores and internal turning. The default choice for most small-bore work. |
| Profiling and contouring | MPR, MXR | Bores with radii, chamfers or stepped contours that a straight boring bar cannot follow. |
| Internal grooving | MGR, MFR, MKR | O-ring seats, relief grooves and retaining-ring grooves. On MGR and MFR the groove width is fixed by the variant's B dimension, so choose the width before the bar. |
| Face grooving | MZR | Grooves turned into a face or shoulder, where the bar approaches along the axis. |
| Internal threading | MIR / MIL | 55° and 60° internal threads in small bores. |
| Larger bores and heavier cuts | NC SHB | Bores from roughly 3 mm to 12 mm, in D12, D16 and D20 holders, where a micro bar no longer has the mass. |
A practical rule: if the bore is straight and the depth is moderate, start with MQR or MUR. Move to MPR or MXR only when the profile demands it — profiling geometry is weaker in the axial direction, so it chatters earlier on a plain bore.
How nose radius changes force and finish
Nose radius is usually chosen last, and it is usually chosen wrong. It does two opposite things at once.
A small radius, R0.05 to R0.1, concentrates the cutting force on a very short edge. It reaches into tight corners and finishes well on light cuts, but there is very little carbide behind the edge to absorb impact. On interrupted cuts, cast surfaces or any setup with runout, it chips first.
A larger radius, R0.2 to R0.5, spreads the load and survives far more abuse, but it raises radial force and increases the minimum bore the tool can enter. It also leaves a larger corner radius, which may not fit the drawing.
Choose by the weakest link in the setup. Rigid machine, clean bore, light finishing pass: a small radius is fine. Older lathe, long overhang, interrupted surface: go up one or two radius steps and take a lighter depth of cut instead.
Overhang: where boring bars actually break
Overhang is the strongest single predictor of failure. A solid carbide bar is stiff, but deflection grows with the cube of the overhang and falls with the fourth power of the diameter. Doubling the overhang makes the bar eight times as flexible at the tip; going from a D4 to a D6 shank at the same length makes it about five times stiffer.
As a working limit, solid carbide bars stay stable to an overhang of roughly four times their diameter. Beyond that you are trading cutting speed for reach, and the loss is steep.
Two things help before you buy a longer bar:
- Shorten the overhang by gripping deeper in the holder, or by approaching the bore from the other end of the part.
- Step up the shank if the bore allows it. The D4 to D6 change buys more rigidity than any parameter adjustment.
If neither is possible, reduce depth of cut first, then feed, then speed. Lowering speed alone rarely fixes chatter: the chip thins, the edge rubs, and the finish gets worse instead of better.
Coolant and coating
Chip evacuation matters more in a small bore than the grade printed on the box. If chips cannot leave, they are recut, and recutting puts the same heat back into the edge a second time. A directed air blast or internal coolant does more for tool life in a 3 mm bore than switching to a harder coating.
Coated micro boring bars hold up better in steel and stainless, where the edge runs hot and adhesion wear dominates. For cast iron and other abrasive workpieces the limiting wear is abrasion rather than heat, so edge strength and a conservative radius matter more than the coating.
In aluminium and copper, the priority is a sharp edge and smooth chip flow rather than coating hardness. A thick coating can round the edge slightly and encourage a built-up edge on soft, gummy material — if finish deteriorates in aluminium, look at edge preparation and coolant before changing grades.
Setup mistakes that get blamed on the tool
- Measuring the wrong bore. A tapered hole needs its minimum diameter, not its entry diameter.
- Assuming the shank is the cutting diameter. On a micro boring bar the shank is the clamping size; the bore it can enter is a separate figure.
- Zeroing on a dirty edge. Touching off on a coated edge with a chip stuck to it puts the whole bore out by the thickness of that chip.
- Using a profiling bar for a straight bore. The extra clearance is not extra versatility; it is less support under load.
- Buying the longest bar "to be safe". Reach you don't need is rigidity you lose.
Frequently asked questions
What is the smallest bore a carbide boring bar can machine?
On the BB Tool MGR and MNR grooving bars, the smallest listed sizes reach approximately 2.1 mm. That figure assumes a rigid setup with controlled runout. Below it, the practical limit is usually vibration rather than the tool.
Should I use a boring bar or a grooving bar for an O-ring seat?
A grooving bar. An O-ring seat is an internal groove, and a boring bar can only open the bore — it cannot cut the side walls.
Why does my boring bar chatter only at the bottom of the bore?
At full depth the bar is at maximum overhang. Chatter that appears only at the bottom is an overhang problem, not a speed problem. Shorten the overhang or step up the shank before touching the parameters.
Can one bar bore and thread the same hole?
Only where the selected variant carries a threading form, as some MQR and MNR sizes do. Otherwise use a dedicated threading bar: the clearance angles for boring and threading are not the same.
Browse the boring range
The Boring Cutter collection lists fourteen BB Tool boring and grooving products, from D3 micro bars to D20 holders, with nose radii from R0.05 to R1.0 and cutting lengths from 4 mm to 40 mm. Each product page gives the exact variant dimensions — check the code against the bore you actually have, not the one on the drawing.